forked from Elron_dev/elbear_arduino_bsp
klassents
0fbfd77518
- начальный загрузчик для плат elbear, elsomik обновлен до версии 0.2.0 - исключено появление краткосрочных просадок при работе ШИМ с максимальным коэффициентом заполнения - добавлена возможность пропускать код стандартного обработчика прерываний при использовании пользовательского обработчика - добавлена возможность конфигурирования вывода на вход с притяжкой к земле (INPUT_PULLDOWN) - исправление известных ошибок
76 lines
1.8 KiB
C++
76 lines
1.8 KiB
C++
#include <OneWire.h>
|
|
|
|
/*
|
|
* DS2408 8-Channel Addressable Switch
|
|
*
|
|
* Writte by Glenn Trewitt, glenn at trewitt dot org
|
|
*
|
|
* Some notes about the DS2408:
|
|
* - Unlike most input/output ports, the DS2408 doesn't have mode bits to
|
|
* set whether the pins are input or output. If you issue a read command,
|
|
* they're inputs. If you write to them, they're outputs.
|
|
* - For reading from a switch, you should use 10K pull-up resisters.
|
|
*/
|
|
|
|
int pin = 10; // P1_4 for Start/Elsomik
|
|
|
|
OneWire net(pin);
|
|
|
|
void PrintBytes(const uint8_t* addr, uint8_t count, bool newline=false) {
|
|
for (uint8_t i = 0; i < count; i++) {
|
|
Serial.print(addr[i]>>4, HEX);
|
|
Serial.print(addr[i]&0x0f, HEX);
|
|
}
|
|
if (newline)
|
|
Serial.println();
|
|
}
|
|
|
|
|
|
void setup(void) {
|
|
Serial.begin(9600);
|
|
}
|
|
|
|
void loop(void) {
|
|
byte addr[8];
|
|
|
|
if (!net.search(addr)) {
|
|
Serial.print("No more addresses.\n");
|
|
net.reset_search();
|
|
delay(1000);
|
|
return;
|
|
}
|
|
|
|
if (OneWire::crc8(addr, 7) != addr[7]) {
|
|
Serial.print("CRC is not valid!\n");
|
|
return;
|
|
}
|
|
|
|
if (addr[0] != 0x29) {
|
|
PrintBytes(addr, 8);
|
|
Serial.print(" is not a DS2408.\n");
|
|
return;
|
|
}
|
|
|
|
Serial.print(" Reading DS2408 ");
|
|
PrintBytes(addr, 8);
|
|
Serial.println();
|
|
|
|
uint8_t buf[13]; // Put everything in the buffer so we can compute CRC easily.
|
|
buf[0] = 0xF0; // Read PIO Registers
|
|
buf[1] = 0x88; // LSB address
|
|
buf[2] = 0x00; // MSB address
|
|
net.write_bytes(buf, 3);
|
|
net.read_bytes(buf+3, 10); // 3 cmd bytes, 6 data bytes, 2 0xFF, 2 CRC16
|
|
net.reset();
|
|
|
|
if (!OneWire::check_crc16(buf, 11, &buf[11])) {
|
|
Serial.print("CRC failure in DS2408 at ");
|
|
PrintBytes(addr, 8, true);
|
|
return;
|
|
}
|
|
Serial.print(" DS2408 data = ");
|
|
// First 3 bytes contain command, register address.
|
|
Serial.println(buf[3], BIN);
|
|
}
|
|
|