удалила лишнее из примеров

libraries/IRremote/examples/SendRawDemo/SendRawDemo.ino

@@ -36,34 +36,34 @@
  */
 #include <Arduino.h>
 
-#if !defined(ARDUINO_ESP32C3_DEV) // This is due to a bug in RISC-V compiler, which requires unused function sections :-(.
-#define DISABLE_CODE_FOR_RECEIVER // Disables static receiver code like receive timer ISR handler and static IRReceiver and irparams data. Saves 450 bytes program memory and 269 bytes RAM if receiving functions are not required.
-#endif
 
 //#define SEND_PWM_BY_TIMER         // Disable carrier PWM generation in software and use (restricted) hardware PWM.
 //#define USE_NO_SEND_PWM           // Use no carrier PWM, just simulate an active low receiver signal. Overrides SEND_PWM_BY_TIMER definition
 //#define NO_LED_FEEDBACK_CODE      // Saves 566 bytes program memory
-//#define USE_OPEN_DRAIN_OUTPUT_FOR_SEND_PIN // Use or simulate open drain output mode at send pin. Attention, active state of open drain is LOW, so connect the send LED between positive supply and send pin!
 
-#include "PinDefinitionsAndMore.h" // Define macros for input and output pin etc.
+#define IR_SEND_PIN 3
+/*
+ * Helper macro for getting a macro definition as string
+ */
+#if !defined(STR_HELPER)
+#define STR_HELPER(x) #x
+#define STR(x) STR_HELPER(x)
+#endif
+
 #include <IRremote.hpp>
 
 void setup() {
     pinMode(LED_BUILTIN, OUTPUT);
 
-    Serial.begin(115200);
+    Serial.begin(9600);
     while (!Serial)
         ; // Wait for Serial to become available. Is optimized away for some cores.
 
-#if defined(__AVR_ATmega32U4__) || defined(SERIAL_PORT_USBVIRTUAL) || defined(SERIAL_USB) /*stm32duino*/|| defined(USBCON) /*STM32_stm32*/ \
-    || defined(SERIALUSB_PID)  || defined(ARDUINO_ARCH_RP2040) || defined(ARDUINO_attiny3217)
-    delay(4000); // To be able to connect Serial monitor after reset or power up and before first print out. Do not wait for an attached Serial Monitor!
-#endif
     // Just to know which program is running on my Arduino
     Serial.println(F("START " __FILE__ " from " __DATE__ "\r\nUsing library version " VERSION_IRREMOTE));
     Serial.println(F("Send IR signals at pin " STR(IR_SEND_PIN)));
 
-    IrSender.begin(); // Start with IR_SEND_PIN -which is defined in PinDefinitionsAndMore.h- as send pin and enable feedback LED at default feedback LED pin
+    IrSender.begin(); // Start with IR_SEND_PIN as send pin and enable feedback LED at default feedback LED pin
 }
 
 /*
@@ -77,8 +77,8 @@ void setup() {
  * e.g. use 560 (instead of 11 * 50) for NEC or use 432 for Panasonic. But in this cases,
  * you better use the timing generation functions e.g. sendNEC() directly.
  */
-const uint8_t rawDataP[] PROGMEM
-= { 180, 90 /*Start bit*/, 11, 11, 11, 11, 11, 34, 11, 11/*0010 0x4 of 8 bit address LSB first*/, 11, 11, 11, 11, 11, 11, 11,
+const uint8_t rawDataP[] = 
+      { 180, 90 /*Start bit*/, 11, 11, 11, 11, 11, 34, 11, 11/*0010 0x4 of 8 bit address LSB first*/, 11, 11, 11, 11, 11, 11, 11,
         11/*0000*/, 11, 34, 11, 34, 11, 11, 11, 34/*1101 0xB*/, 11, 34, 11, 34, 11, 34, 11, 34/*1111*/, 11, 11, 11, 11, 11, 11, 11,
         34/*0001 0x08 of command LSB first*/, 11, 34, 11, 11, 11, 11, 11, 11/*1000 0x01*/, 11, 34, 11, 34, 11, 34, 11,
         11/*1110 Inverted 8 of command*/, 11, 11, 11, 34, 11, 34, 11, 34/*0111 inverted 1 of command*/, 11 /*stop bit*/};
@@ -94,8 +94,6 @@ const uint16_t rawData[] = { 9000, 4500/*Start bit*/, 560, 560, 560, 560, 560, 1
         1690/*1111 inverted 0 of command*/, 560 /*stop bit*/}; // Using exact NEC timing
 
 void loop() {
-
-#if FLASHEND > 0x1FFF // For more than 8k flash => not for ATtiny85 etc.
     /*
      * Send hand crafted data from RAM
      */
@@ -105,8 +103,6 @@ void loop() {
 
     delay(1000); // delay must be greater than 8 ms (RECORD_GAP_MICROS), otherwise the receiver sees it as one long signal
 
-#endif
-
     /*
      * Send byte data direct from FLASH
      * Note the approach used to automatically calculate the size of the array.