перенесла переключение ноги spi в платозависимый файл variants.c

libraries/SPI/src/SPI.cpp

@@ -1,6 +1,5 @@
 #include "SPI.h"
 #include "mik32_hal_spi.h"
-#include "utility/spiElbear.h"
 
 SPI_HandleTypeDef hspi;
 bool newConfig = false;

libraries/SPI/src/utility/spiElbear.cpp

@@ -1,53 +0,0 @@
-#include "Arduino.h"
-#include "spiElbear.h"
-#include "mik32_hal_gpio.h"
-#include "xprintf.h"
-
-// pins shift in registers
-#define PIN_3_SHIFT  3
-#define PIN_4_SHIFT  4
-#define PORT1_GET_PAD_CONFIG(pinShift)  ((PAD_CONFIG->PORT_1_CFG  >> (pinShift<<1)) & 0b11)
-#define PORT1_GET_PAD_PUPD(pinShift)    ((PAD_CONFIG->PORT_1_PUPD >> (pinShift<<1)) & 0b11)  
-#define PORT1_GET_GPIO_STATE(pinShift)  ((GPIO_1->OUTPUT_ >> pinShift) & 0b1)  
-
-void spi_onBegin(void)
-{
-    // there is a seller on pin 1.6 which replace D10 from spi NSS pin 1.3 to pin 1.4, 
-    // because spi needs pin 1.3 for correct work
-
-    // replace config from 1.3 to 1.4 
-    uint8_t config = PORT1_GET_PAD_CONFIG(PIN_3_SHIFT);
-    if (config == 0)    // common gpio
-    {
-        // get info from pin gpio1.3 and set config to gpio1.4
-        HAL_GPIO_PinConfig(GPIO_1, GPIO_PIN_4, HAL_GPIO_GetPinDirection(GPIO_1, GPIO_PIN_3), 
-                            (HAL_GPIO_PullTypeDef)PORT1_GET_PAD_PUPD(PIN_3_SHIFT), HAL_GPIO_DS_2MA);
-        HAL_GPIO_WritePin(GPIO_1, GPIO_PIN_4,  (GPIO_PinState)PORT1_GET_GPIO_STATE(PIN_3_SHIFT));
-        
-        // pin D10 was switched to different gpio and can be used further
-    }
-    else if(config == 2)  // timer for pwm
-    {
-        // if D10 (spi NSS pin) was used as pwm, we need to stop timer,
-        // because 1.4 don't support timer
-        analogWriteStop(10);
-        ErrorMsgHandler("analogWrite(): D10 cannot be used as PWM pin while SPI is running");
-    }
-    
-    // switch seller to pin 1.4
-    HAL_GPIO_PinConfig(GPIO_1, GPIO_PIN_6, HAL_GPIO_MODE_GPIO_OUTPUT, HAL_GPIO_PULL_NONE, HAL_GPIO_DS_2MA);
-    HAL_GPIO_WritePin(GPIO_1, GPIO_PIN_6, GPIO_PIN_HIGH);
-    blockSpiPin();
-}
-
-void spi_onEnd(void)
-{
-    // get info from pin gpio1.4 and set config to gpio1.3
-    HAL_GPIO_PinConfig(GPIO_1, GPIO_PIN_3, HAL_GPIO_GetPinDirection(GPIO_1, GPIO_PIN_4), 
-                        (HAL_GPIO_PullTypeDef)PORT1_GET_PAD_PUPD(PIN_4_SHIFT), HAL_GPIO_DS_2MA);
-    HAL_GPIO_WritePin(GPIO_1, GPIO_PIN_3,  (GPIO_PinState)PORT1_GET_GPIO_STATE(PIN_4_SHIFT));
-
-    // switch seller back to pin 1.3
-    HAL_GPIO_WritePin(GPIO_1, GPIO_PIN_6, GPIO_PIN_LOW);
-    unblockSpiPin();
-}

libraries/SPI/src/utility/spiElbear.h

@@ -1,3 +0,0 @@
-
-void spi_onBegin(void);
-void spi_onEnd(void);