v0.5.3

- начальный загрузчик для плат elbear, elsomik обновлен до версии 0.2.0
- исключено появление краткосрочных просадок при работе ШИМ с максимальным коэффициентом заполнения
- добавлена возможность пропускать код стандартного обработчика прерываний при использовании пользовательского обработчика
- добавлена возможность конфигурирования вывода на вход с притяжкой к земле (INPUT_PULLDOWN)
- исправление известных ошибок

libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino

@@ -5,13 +5,14 @@
  Receives from software serial, sends to hardware serial.
 
  The circuit:
- * RX is digital pin 2 (connect to TX of other device)
- * TX is digital pin 6 (connect to RX of other device)
+ * RX is digital pin 2 (P0_10) (connect to TX of other device)
+ * TX is digital pin 6 (P0_2) (connect to RX of other device)
 
  Note:
- Not all pins on the Elbear Ace-Uno support interrupts,
- so only the following can be used for RX:
- 2, 3, 4, 5, 8, 9
+ Not all pins on the Elbear Ace-Uno/Ace-Nano support interrupts,
+ so only the following can be used for RX: 2, 3, 4, 5, 8, 9
+ Elsomik board pins with interrupts: P0_8, P1_4, P1_5, P1_6, P1_9, P1_10, P1_15, P2_7
+ Start board pins with interrupts: P0_10, P0_12, P0_13, P0_14, P0_15, P1_9, P1_15
 
  created back in the mists of time
  modified 25 May 2012
@@ -22,8 +23,9 @@
 
  */
 #include <SoftwareSerial.h>
-
-SoftwareSerial mySerial(2, 6); // RX, TX
+int rx_pin = 2; // P1_9 for Start/Elsomik
+int tx_pin = 6; // P0_2 for Start/Elsomik
+SoftwareSerial mySerial(rx_pin, tx_pin); 
 
 void setup() {
   // Open serial communications and wait for port to open:

libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino

@@ -17,17 +17,22 @@
  * Second serial device's TX attached to digital pin 8(RX), RX to pin 10(TX)
 
  Note:
- Not all pins on the Elbear Ace-Uno support interrupts,
- so only the following can be used for RX:
- 2, 3, 4, 5, 8, 9
+ Not all pins on the Elbear Ace-Uno/Ace-Nano support interrupts,
+ so only the following can be used for RX: 2, 3, 4, 5, 8, 9
+ Elsomik board pins with interrupts: P0_8, P1_4, P1_5, P1_6, P1_9, P1_10, P1_15, P2_7
+ Start board pins with interrupts: P0_10, P0_12, P0_13, P0_14, P0_15, P1_9, P1_15
  */
 
 #include <SoftwareSerial.h>
 
 // software serial #1: RX = digital pin 2, TX = digital pin 6
-SoftwareSerial portOne(2, 6);
+int rx_pin_1 = 2; // P1_9 for Start/Elsomik
+int tx_pin_1 = 6; // P0_2 for Start/Elsomik
+SoftwareSerial portOne(rx_pin_1, tx_pin_1);
 // software serial #2: RX = digital pin 8, TX = digital pin 10
-SoftwareSerial portTwo(8, 10);
+int rx_pin_2 = 8;  // P1_15 for Start/Elsomik
+int tx_pin_2 = 10; // P1_3 for Start/Elsomik
+SoftwareSerial portTwo(rx_pin_2, tx_pin_2);
 
 // active port is changed by user button pressing
 volatile bool isPortOneActive = true;